nass-micro-station-measurements/disturbance-ty-sr/index.org

• Measurement description
  • Setup
  • Goal
  • Measurements
• Data Analysis
  • ZIP file containing the data and matlab files
  • Load data
  • Voltage to Velocity
  • Time domain plots
  • Frequency Domain
  • Ty motion and current
    • Data pre-processing
    • Time domain data
  • Conclusion

#+TITLE:Vibrations induced by simultaneous scans of the translation stage and of the slip-ring

Measurement description

Setup   ignore

Setup: All the stages are OFF except the translation stage and the Slip-Ring.

Each of the signal is amplified by voltage amplifiers with the following settings:

• Gain: 40dB
• AC/DC option: AC
• Low pass filter: 1kHz

The slip-ring is rotating at 60rpm. At the same time, scans with the translation stage are done at 1Hz with an amplitude of 600000cnt (= 3mm).

Two geophones are used to measure the motion in the vertical direction of the marble and of the sample.

Goal   ignore

Goal:

• The goal is to estimate the vibrations induced by the simultaneous scans of the spindle (here the slip-ring is used as the spindle is not fully functional yet) and of the translation stage

Measurements   ignore

Measurements:

Three measurements are done:

Measurement File	Description
mat/data_050.mat	Slip-Ring at 1Hz, Ty OFF
mat/data_051.mat	Slip-Ring at 1Hz, Ty ON (The current and cnt error of Ty is also registered)
mat/data_052.mat	Slip-Ring at 1Hz, Ty 1Hz 600000cnt

Each of the measurement mat file contains one data array with 3 columns:

Column number	Description
1	Geophone on the marble
2	Geophone at the sample location
3	Time

Data Analysis

<<sec:disturbance_ty_sr>>

ZIP file containing the data and matlab files   ignore

All the files (data and Matlab scripts) are accessible here.

Load data

  ty_of = load('mat/data_050.mat', 'data'); ty_of = ty_of.data;
  ty_on = load('mat/data_051.mat', 'data'); ty_on = ty_on.data;
  ty_1h = load('mat/data_052.mat', 'data'); ty_1h = ty_1h.data;

Voltage to Velocity

We convert the measured voltage to velocity using the function voltageToVelocityL22 (accessible here).

  gain = 40; % [dB]

  ty_of(:, 1) = voltageToVelocityL22(ty_of(:, 1), ty_of(:, 3), gain);
  ty_on(:, 1) = voltageToVelocityL22(ty_on(:, 1), ty_on(:, 3), gain);
  ty_1h(:, 1) = voltageToVelocityL22(ty_1h(:, 1), ty_1h(:, 3), gain);

  ty_of(:, 2) = voltageToVelocityL22(ty_of(:, 2), ty_of(:, 3), gain);
  ty_on(:, 2) = voltageToVelocityL22(ty_on(:, 2), ty_on(:, 3), gain);
  ty_1h(:, 2) = voltageToVelocityL22(ty_1h(:, 2), ty_1h(:, 3), gain);

Time domain plots

We plot the measured velocity of the marble (figure fig:ty_marble_time), sample (figure fig:ty_sample_time) and the relative velocity of the sample with respect to the marble (figure fig:ty_relative_time).

We also integrate the relative velocity to obtain the relative displacement (figure fig:ty_relative_disp_time).

  figure;
  hold on;
  plot(ty_1h(:, 3), ty_1h(:, 1), 'DisplayName', 'Marble - Ty 1Hz');
  plot(ty_on(:, 3), ty_on(:, 1), 'DisplayName', 'Marble - Ty ON');
  plot(ty_of(:, 3), ty_of(:, 1), 'DisplayName', 'Marble - Ty OFF');
  hold off;
  xlabel('Time [s]'); ylabel('Velocity [m/s]');
  xlim([0, 2]);
  legend('Location', 'southwest');

  <<plt-matlab>>

Velocity of the marble in the vertical direction

  figure;
  hold on;
  plot(ty_1h(:, 3), ty_1h(:, 2), 'DisplayName', 'Sample - Ty - 1Hz');
  plot(ty_on(:, 3), ty_on(:, 2), 'DisplayName', 'Sample - Ty - ON');
  plot(ty_of(:, 3), ty_of(:, 2), 'DisplayName', 'Sample - Ty - OFF');
  hold off;
  xlabel('Time [s]'); ylabel('Velocity [m/s]');
  xlim([0, 2]);
  legend('Location', 'southwest');

  <<plt-matlab>>

Velocity of the sample in the vertical direction

  figure;
  hold on;
  plot(ty_1h(:, 3), ty_1h(:, 2)-ty_1h(:, 1), 'DisplayName', 'Relative Velocity - Ty - 1Hz');
  plot(ty_on(:, 3), ty_on(:, 2)-ty_on(:, 1), 'DisplayName', 'Relative Velocity - Ty - ON');
  plot(ty_of(:, 3), ty_of(:, 2)-ty_of(:, 1), 'DisplayName', 'Relative Velocity - Ty - OFF');
  hold off;
  xlabel('Time [s]'); ylabel('Velocity [m/s]');
  xlim([0, 2]);
  legend('Location', 'southwest');

  <<plt-matlab>>

Relative velocity of the sample with respect to the marble

  figure;
  hold on;
  plot(ty_1h(:, 3), lsim(1/s, ty_1h(:, 2)-ty_1h(:, 1), ty_1h(:, 3)), 'DisplayName', 'Relative Displacement- Ty - 1Hz');
  plot(ty_on(:, 3), lsim(1/s, ty_on(:, 2)-ty_on(:, 1), ty_on(:, 3)), 'DisplayName', 'Relative Displacement- Ty - ON');
  plot(ty_of(:, 3), lsim(1/s, ty_of(:, 2)-ty_of(:, 1), ty_of(:, 3)), 'DisplayName', 'Relative Displacement- Ty - OFF');
  hold off;
  xlabel('Time [s]'); ylabel('Displacement [m]');
  xlim([0, 2]);
  legend('Location', 'southwest');

  <<plt-matlab>>

Relative Displacement of the sample with respect to the marble

Frequency Domain

We first compute some parameters that will be used for the PSD computation.

  dt = ty_of(2, 3)-ty_of(1, 3);

  Fs = 1/dt; % [Hz]

  win = hanning(ceil(10*Fs));

Then we compute the Power Spectral Density using pwelch function.

First for the geophone located on the marble

  [pxof_m, f] = pwelch(ty_of(:, 1), win, [], [], Fs);
  [pxon_m, ~] = pwelch(ty_on(:, 1), win, [], [], Fs);
  [px1h_m, ~] = pwelch(ty_1h(:, 1), win, [], [], Fs);

And for the geophone located at the sample position.

  [pxof_s, f] = pwelch(ty_of(:, 2), win, [], [], Fs);
  [pxon_s, ~] = pwelch(ty_on(:, 2), win, [], [], Fs);
  [px1h_s, ~] = pwelch(ty_1h(:, 2), win, [], [], Fs);

Finally, for the relative velocity.

  [pxof_r, f] = pwelch(ty_of(:, 2)-ty_of(:, 1), win, [], [], Fs);
  [pxon_r, ~] = pwelch(ty_on(:, 2)-ty_on(:, 1), win, [], [], Fs);
  [px1h_r, ~] = pwelch(ty_1h(:, 2)-ty_1h(:, 1), win, [], [], Fs);

And we plot the ASD of the measured velocities:

• figure fig:psd_marble_compare for the geophone located on the marble
• figure fig:psd_sample_compare for the geophone at the sample position
• figure fig:psd_relative_compare for the relative velocity

  figure;
  hold on;
  plot(f, sqrt(px1h_m), 'DisplayName', 'Marble - Ty 1Hz');
  plot(f, sqrt(pxon_m), 'DisplayName', 'Marble - Ty ON');
  plot(f, sqrt(pxof_m), 'DisplayName', 'Marble - Ty OFF');
  hold off;
  set(gca, 'xscale', 'log');
  set(gca, 'yscale', 'log');
  xlabel('Frequency [Hz]'); ylabel('ASD of the measured velocity $\left[\frac{m/s}{\sqrt{Hz}}\right]$')
  legend('Location', 'southwest');
  xlim([1, 500]);

  <<plt-matlab>>

Comparison of the ASD of the measured velocities from the Geophone on the marble

  figure;
  hold on;
  plot(f, sqrt(px1h_s), 'DisplayName', 'Sample - Ty 1Hz');
  plot(f, sqrt(pxon_s), 'DisplayName', 'Sample - Ty ON');
  plot(f, sqrt(pxof_s), 'DisplayName', 'Sample - Ty OFF');
  hold off;
  set(gca, 'xscale', 'log');
  set(gca, 'yscale', 'log');
  xlabel('Frequency [Hz]'); ylabel('ASD of the measured velocity $\left[\frac{m/s}{\sqrt{Hz}}\right]$')
  legend('Location', 'southwest');
  xlim([1, 500]);

  <<plt-matlab>>

Comparison of the ASD of the measured velocities from the Geophone at the sample location

  figure;
  hold on;
  plot(f, sqrt(px1h_r), 'DisplayName', 'Relative - Ty 1Hz');
  plot(f, sqrt(pxon_r), 'DisplayName', 'Relative - Ty ON');
  plot(f, sqrt(pxof_r), 'DisplayName', 'Relative - Ty OFF');
  hold off;
  set(gca, 'xscale', 'log');
  set(gca, 'yscale', 'log');
  xlabel('Frequency [Hz]'); ylabel('ASD of the measured velocity $\left[\frac{m/s}{\sqrt{Hz}}\right]$')
  legend('Location', 'southwest');
  xlim([1, 500]);

  <<plt-matlab>>

Comparison of the ASD of the relative velocity

Ty motion and current

The position of the translation stage and current flowing in its actuator are measured using the elmo software and saved as an csv file.

Data pre-processing

Let's look at at the start of the csv file.

  sed -n 1,30p mat/Ty-when-Rz-1Hz-and-Ty-1Hz.csv | nl -ba -

     1	Elmo txt chart ver 2.0
     2
     3	[File Properties]
     4	Creation Time,2019-05-13 05:33:43
     5	Last Updated,2019-05-13 05:33:43
     6	Resolution,0.001
     7	Sampling Time,5E-05
     8	Recording Time,5.461
     9
    10	[Chart Properties]
    11	No.,Name,X Linear,X No.
    12	1,Chart #1,True,0
    13	2,Chart #2,True,0
    14
    15	[Chart Data]
    16	Display No.,X No.,Y No.,X Unit,Y Unit,Color,Style,Width
    17	1,1,2,sec,N/A,ff0000ff,Solid,TwoPoint
    18	2,1,3,sec,N/A,ff0000ff,Solid,TwoPoint
    19	2,1,4,sec,N/A,ff007f00,Solid,TwoPoint
    20
    21	[Signal Names]
    22	1,Time (sec)
    23	2,Position [cnt]
    24	3,Current Command [A]
    25	4,Total Current Command [A]
    26
    27	[Signals Data Group 1]
    28	1,2,3,4,
    29	0,-141044,-0.537239575086517,-0.537239575086517,
    30	0.001,-143127,-0.530803752974691,-0.530803752974691,

The real data starts at line 29. We then load this cvs file starting at line 29.

  tye_on = csvread("mat/Ty-when-Rz-1Hz.csv", 29, 0);
  tye_1h = csvread("mat/Ty-when-Rz-1Hz-and-Ty-1Hz.csv", 29, 0);

Time domain data

We plot the position of the translation stage measured by the encoders.

There is 200000 encoder count for each mm, we then divide by 200000 to obtain mm.

The result is shown on figure fig:ty_position_time.

  figure;
  subplot(1, 2, 1);
  plot(tye_on(:, 1), (tye_on(:, 2)-mean(tye_on(:, 2)))/200000);
  xlim([0, 5]);
  xlabel('Time [s]'); ylabel('Position [mm]');
  legend({'Ty - ON'}, 'Location', 'northeast');

  subplot(1, 2, 2);
  plot(tye_1h(:, 1), (tye_1h(:, 2)-mean(tye_1h(:, 2)))/200000);
  xlim([0, 5]);
  xlabel('Time [s]'); ylabel('Position [mm]');
  legend({'Ty - 1Hz'}, 'Location', 'northeast');

  <<plt-matlab>>

Y position of the translation stage measured by the encoders

We also plot the current as function of the time on figure fig:ty_current_time.

  figure;
  subplot(1, 2, 1);
  plot(tye_on(:, 1), tye_on(:, 3)-mean(tye_on(:, 3)));
  xlim([0, 5]);
  xlabel('Time [s]'); ylabel('Current [A]');
  legend({'Ty - ON'}, 'Location', 'northeast');

  subplot(1, 2, 2);
  plot(tye_1h(:, 1), tye_1h(:, 3)-mean(tye_1h(:, 3)));
  xlim([0, 5]);
  xlabel('Time [s]'); ylabel('Current [A]');
  legend({'Ty - 1Hz'}, 'Location', 'northeast');

  <<plt-matlab>>

Current going through the actuator of the translation stage

Conclusion